News

Jun 29, 2023

Kinetic and thermodynamic study in piezo degradation of methylene blue by SbSI/Sb2S3 nanocomposites stimulated by zirconium oxide balls

Scientific Reports volume 12, Article number: 15242 (2022) Cite this article 1348 Accesses 5 Citations 3 Altmetric Metrics details Mechanical energy harvesting by piezoelectric materials to drive

Scientific Reports volume 12, Article number: 15242 (2022) Cite this article

1348 Accesses

5 Citations

3 Altmetric

Metrics details

Mechanical energy harvesting by piezoelectric materials to drive catalysis reactions received extensive attention for environmental remediation. In this work, SbSI/Sb2S3 nanocomposites were synthesized as a catalyst. ZrO2 balls were used as an alternative mechanical force to ultrasonic for stimulating the piezocatalyst for the first time. The kinetics and thermodynamics of the piezo degradation of methylene blue (MB) were studied deeply. Besides the effect of the type of mechanical force, the number of ZrO2 balls, and temperature of the reaction on the degradation efficiency were studied. Here mechanical energy came from the collision of the ZrO2 balls with the catalyst particles. Using ZrO2 balls instead of ultrasonic vibration led to enhance degradation efficiency by 47% at 30 ± 5 °C. A kinetic study revealed that piezo degradation of methylene blue (MB) by SbSI/Sb2S3 catalyst followed pseudo-second-order kinetics. Based on thermodynamic results piezo degradation of MB was an exothermic reaction.

Developing alternative clean and sustainable energy sources has been drawing intense research interest in relieving environmental pollution and energy crises. Materials that can gather and convert solar or mechanical energy have been extensively researched in recent years as a new form of clean energy1,2,3,4,5,6,7,8. Piezo materials are considered an interesting class of material that can harvest and convert mechanical energy to electrical or chemical energy9,10,11,12. In this scenario, when the piezo material was forced under applied deformation caused by the mechanical force, the piezoelectric potential will shift the electronic energy levels of unoccupied or occupied states within the materials. In other words, it lowers the conduction band (CB) of the piezo material to below the highest occupied molecular orbital (HOMO) of the molecule of piezo material. Therefore, the electrons could transfer from the HOMOs of molecules to the CB of piezo material13,14,15,16,17. In the past, piezo materials mainly were used as sensors, transducers, and electronic industries18,19,20. Recently a new application was found, referred to as piezocatalysis. Till now, antibacterial and water splitting have been achieved via piezocatalysis. More recently, piezocatalysis were applied as a treatment agent to break down water pollutants which is one of the most severe environmental issues for human beings because some of these pollutants are highly soluble and chemically stable. Various types of materials were developed for this purpose, such as the 1D and 2 D wurtzite ZnO and BaTiO321,22. For example, in 2019, Qian et al. reported decomposing of ~ 94% of rhodamine B (RhB) dye by using barium titanate (BaTiO3, BTO)–polydimethylsiloxane composite23. Later in 2020, Raju et al. applied Polyvinylidene Fluoride/ZnSnO3 Nanocube/Co3O4 composite to treat RhB and methylene blue (MB)24. Xu and his coworker degraded over 97% of RhB using Bi0.5Na0.5TiO3@TiO2 Composite25.

Employing piezocatalysis for environmental remediation has advantages compared to the other methods such as photocatalysis26, adsorbent27, and the Fenton process28. For example, photocatalysis only works under light. Besides, wide bandgap semiconductors are needed to avoid recombination of carrier charges. Using a wide-bandgap catalyst requires high-energy photons, and the material is usually more costly29,30,31,32,33,34.

Recently several articles published the mechanism behind the degradation of pollutants by piezoelectric materials. For example, we applied PbTiO3 nanostructures to treat acid red 143 and acid violet in water. We studied the possible mechanism by using radical scavengers and suggested that free radicals are responsible for degradation of organic pollutants35. Later in 2021, Lin et al. reported use of BaTiO3 nanocubes as piezo catalysts to treat organic pollutants and suggested the same mechanism36. Although several groups tried to study the possible mechanism behind it, the kinetics of degradation of organic pollutants by piezoelectric material is rarely studied. For instance, Lei et al studied the kinetics behind piezocatalytic degradation of dichlorophenols using two-dimensional graphitic carbon nitride. They reported that the degradation of dichlorophenols is pseudo-first-order kinetics37. However, the thermodynamics, effect of temperature, and amount of applied force on the kinetic of piezocatalytic degradation of pollutant were not discussed yet. Besides previous reports used ultrasonic actuation as a source of mechanical force, while we used zirconia balls to provide mechanical forces. Here we prepared piezo catalyst by sonochemistry and hydrothermal method. Then we studied the related kinetics at varied temperatures of 293 K, 303 K, and 313 K, and under different mechanical forces. Finally, we studied the thermodynamics behind the degradation.

Antimony sulfate (Sb2(SO4)3), Iodine, and sulfur were used as precursor materials without any purification and processing. 1.5 mm Diameter Zirconia Oxide Ceramic balls with hardness of HRA 87-91 were used to stimulate the piezo catalyst. The crystal structure of the samples was investigated by an X-ray diffractometer (Philips X'pert Pro MPD, The Netherlands) with Ni-filtered Cu Kα radiation (λ = 1.54 Å). The sonochemical process was performed by an ultrasonic bath of a 20 kHz ultrasonic device with a maximum output power of 250 W. EDS (energy dispersion spectroscopy) analysis was performed using an X-Max Oxford, England. ƩIGMA/VP- ZEISS, Germany was used to recording SEM images. To take the SEM images all samples were coated with gold. TEM images were captured by using transmission electron microscopy (TEM, Zeiss).

To synthesize SbSI/Sb2S3 nanocomposites by sonochemistry method first 2 g of Sb2(SO4)3, 0.95 g of Iodine, and 0.24 g of sulfur weighted. Then, mixed those in 100 mL ethanol under stirring for 10 min. Afterward, the above solution was sonicated in an ultrasonic bath with 250 W in power for 2 h. Products were separated and washed several times, followed by drying overnight at 70 °C (sample S1). In the case of sample S2, the ultrasonic time was changed to 3 h.

The solvothermal method was used as an alternative method to prepare SbSI/Sb2S3 nanocomposites. In this case, 2 g of Sb2(SO4)3, 0.95 g of Iodine, and 0.24 g of sulfur were weighted and mixed in 40 mL of ethanol under stirring for 10 min. Afterward, the above mixture was transferred to stainless steel autoclave and heated at 180 °C for 6 h. finally, the product was separated and washed several times with water and ethanol and dried at 70 °C, This sample was labeled as S3. The next sample which was labeled as S4 was prepared with the same recipe and hydrothermal temperature of 245 °C. Samples S5 and S6 were prepared to study the effect of hydrothermal time on the morphology and purity of products. Hydrothermal time for samples S5 and S6 was 4 h and 8 h, respectively. The detail in the preparation of Samples S1–S6 could be found in Table S1 as supporting information.

The piezocatalytic activities of SbSI/Sb2S3 nanocomposites are evaluated by degrading Methylene blue (MB). 1 g L−1 of SbSI/Sb2S3 nanocomposites was added to the 12.5 mL of Methylene blue with different concentrations and was stirred in dark for 30 min to equilibrium adsorption–desorption of dye on the catalyst. In the case of using ultrasonic as mechanical force, the mixture of dye solution and catalyst was sonicated in dark at different times. After a certain time, the UV–Vis of samples was taken to monitor the degradation efficiency of MB. In the other reaction batches, zirconium oxide balls were used instead of ultrasonic to supply force to stimulate piezocatalyst. The numbers of zirconium oxide balls were optimized by studying the effect of different number of balls on the degradation of MB.

The effect of preparation condition of catalyst, time, temperature, type of mechanical force, amount of mechanical force was studied on the piezocatalytic activities of SbSI/Sb2S3 nanocomposites.

The study of reaction kinetics was performed by collecting the sample every 5 min while the temperature was controlled at the indicated temperatures. The experiments for piezo degradation isotherm evaluation were carried out in a batch system with the MB concentration range of 5 and 10 ppm at three different temperatures of 293 K, 303 K, and 313 K, during 90 min of reaction.

The pseudo-first-order rate constants and pseudo-second-order rate constants were determined by a non-linear curve fitting to the first-order and second-order reaction equation. Activation parameters were determined by fitting the data to the linearized form of the Eyring equation.

SbSI/Sb2S3 nanocomposites were prepared by modification of the sonication method according to the ref38. Besides, SbSI/Sb2S3 nanocomposites were prepared by the solvothermal method. The XRD and EDS of prepared samples were presented in Figure S1 and Figures S2–S7. XRD pattern of samples S1–S6 in Figure S1 showed that S3 had an amorphous structure, while other samples crystallized as orthorhombic SbSI and orthorhombic Sb2S3 closely matched well with the previous reports on the XRD pattern of SbSI nanostructures39,40,41,42. EDS results for the qualitative analysis of SbSI/Sb2S3 nanocomposites were presented in Figures S2–S7 and approved the presence of elements S, Sb, and I in prepared samples which could be assigned SbSI/Sb2S3 nanocomposites. In all spectra, the Au peak was observed due to the use of gold for surface conductivity for SEM analysis.

SEM images of samples S1–S6 was illustrated in Fig. 1a–f which showed that S1 mainly consists of aggregated nanoparticles (Fig. 1a). As depicted in Fig. 1b, uniform micro-size rods of SbSI/Sb2S3 nanocomposites were formed by increasing sonication time to 3 h. The morphology of the solvothermal synthesized SbSI/Sb2S3 nanocomposites at 180 °C for 6 h was depicted in Fig. 1c, where they exist in a regular rod shape with an average diameter of about 400 nm. Figure 1d displays the SEM image of the sample prepared by the solvothermal method at 245 °C where a mixture of more thick rods and nano-sized plates were formed. Changing the solvothermal time to 4 h at 180 °C led to the form of belt-like structures (Fig. 1e). The SEM image of sample S6 is shown in Fig. 1f, where very thick plate-like structures appeared. Due to the high reaction time belt-like structures stuck together and form thick plate-like structures. TEM images of sample S4 that was prepared by solvothermal at 245 °C were illustrated in Fig. 2. TEM images show that hexagonal shape nanostructures with an average size of 40–70 nm form rod-likes and plate-like structures.

SEM images of piezo catalysts prepared (a) by sonochemistry for 2 h (S1), (b) sonochemistry for 3 h (S2), (c) by solvothermal method at 180 °C for 6 h (S3), (d) by solvothermal method at 245 °C for 6 h (S4), (e) by solvothermal method at 180 °C for 4 h (S5), and (f) by solvothermal method at 245 °C for 8 h (S6).

TEM images of sample prepared by solvothermal at 245 °C for 6 h (S4).

First, the effect of the number of ZrO2 balls added to the solution was studied by using 0, 5, 10, and 15 balls at 25 ± 5 °C. Results were summarized in Fig. 3a, b, it showed the degradation of 10 ppm MB was about 34% when there was no ball in the shaker (shaking RPM = 350). Degradation increased to 89.1% by adding 5 balls to the reactor. It happens because of increasing mechanical force produced by kinetic energy from the collision of the balls with the catalyst and the balls together. Increasing the number of balls to 10 led to a decrease in degradation efficiency to 72.9%. Finally, 15 balls were used in the reactor which degradation efficiency of 58.8% was achieved by using sample S4 as the catalyst. So 5 ZrO2 balls were used in the next studies, degradation in the presence of 5 balls was higher than 10 and 15 balls because 5 balls provided more kinetic energy (mechanical energy) to stimulate the catalyst. This can be seen in the detail about the momentum of balls in fluid and slow-motion videos of 5, 10, and 15 ZrO2 balls in water as a simulation of the degradation reactor of MB as presented in supporting information (Figure S8).

(a) Degradation efficiency of 10 ppm of MB in presence of sample S4 by using different ZrO2 balls as source of mechanical energy, (b) related spectrum of MB. (c) degradation efficiency of MB by using samples S-S6 with shaking speed of 250 RPM at 30 ± 2 °C for 1 h and related spectrum (d).

Another parameter that affects the degradation efficiency of MB by SbSI/Sb2S3 nanocomposites was the type and amount of mechanical force. Results for using a shaker in the presence of ZrO2 balls without a catalyst at 250 RPM, using a shaker in the presence of a catalyst at 250 RPM, using a shaker in presence of both the catalyst and ZrO2 balls at 150, 250, and 350 RPM, and using ultrasonic bath are presented in Figure S9 (supporting information). By applying ZrO2 balls without catalyst at 250 RPM and 30 ± 5 °C only 3.5% of MB was decomposed. Repeat the test in the presence of the catalyst and without balls at the same shaking speed and temperature leading to degrading 12.8% of MB. Adding catalyst and ZrO2 balls decompose 25.7% of MB at the same shaking speed and temperature. By increasing shaking speeds to 350 RPM in the presence of catalyst and balls, degradation efficiency increased to 67.2% at 30 ± 5 °C. However, 15.2% of MB was decomposed in the presence of catalyst and balls when the shaking speed decreased to 150 RPM. Finally, applying 250 W in power ultrasonic waves as mechanical force decomposed 45.7% of MB at 30 ± 5 °C.

The effect of different samples on the degradation of MB was investigated by using 5 balls. Differently prepared samples were used as piezo catalysts with less than 250 RPM at 30 ± 2 °C for 1 h and the results were depicted in Fig. 3c, d. Following degradation efficiencies were achieved for sample S1–S6, respectively: 22.4%, 9.1%, 10.8%, 20.8%, 8.6%, and 8.5%. The first sample prepared by ultrasonic for 2 h shows the highest degradation efficiency.

The mechanism behind the degradation by ZrO2 balls and piezo catalyst is schematically illustrated in Fig. 4. When piezo catalyst particles collided with ZrO2 balls, electrons and holes were produced in the piezo catalyst. Generated electrons and holes reacted with oxygen and water molecules and produced oxidation radicals that could decompose dye pollutants.

Schematically illustration of degradation of MB dye by SbSI/Sb2S3 nanocomposites in presence of ZrO2 balls.

Figure 5a, b illustrate the effect of the initial concentration of dye and shaking time on the degradation of MB. Figure 5a demonstrates the degradation of MB over time by using S4 as the catalyst at 30 ± 5 °C. 47.7% of MB was degraded during 1 h of sonication in an ultrasonic bath at 250 W. By repeating the test on the shaker at a shaking speed of 350 RPM, degradation efficiency increased to 67.2%. Sample S4 showed a lower degradation efficiency compared to the result presented in Fig. 3a because the experiment in Fig. 3a was done at a lower temperature, the effect of reaction temperature on degradation efficiency will be discussed later. The effect of the initial concentration of dye on the degradation efficiency of MB is presented in Fig. 5b, related spectrum is presented in Fig. 5c. Degradation efficiency for 5, 10, 15, and 20 ppm of MB was tested by using 5 balls at 250 RPM at 30 ± 0.5 °C. Based on these results, degradation efficiency was increased by increasing the initial dye concentration. In the case of 5 and 10 ppm, 24.7% and 25.7% of MB were degraded while 29% and 37% of MB were degraded in case of 15 and 20 ppm of pollutant.

(a) Degradation MB by using S4 as a catalyst and ultrasonic bath with 250 W in power (red curve) and ZrO2 balls as vibration source (black curve), (b) removal percentages of different dye concentrations, and related spectrum (c), (d) degradation efficiency of 5 ppm and 10 ppm of MB in presence of sample S4 by using 5 ZrO2 balls. (e) Degradation percentages of MB degradation over time at 20 °C (brown curve), 40 °C (blue curve), and 70 °C (black curve).

Another parameter that significantly affects degradation efficiency in piezo degradation was temperature. To figure out this effect, piezo degradation was studied at 5 different temperatures including 20, 30, 40, 50, and 70 °C. As proven in Fig. 5d, degradation efficiency decreased over temperatures, and removal percentages of MB decreased from 25.7% and 27.9% for 5 and 10 ppm of MB at 20 °C with 250 RPM to 16.1% and 19.5% at 70 °C and 250 RPM. Figure 5e shows the degradation efficiency over time for 10 ppm MB at 20 °C, 40 °C, and 70 °C. Based on the results, degradation efficiency was decreased by more than 30% by increasing the temperature of shaking from 20 to 70 °C. This happens because we were close to the curie temperature by increasing the temperature and the catalyst will show a more symmetric structure41,42.

The kinetics of degradation and characteristic constants of degradation by piezocatalyst can be studied through kinetic measurements using pseudo-first-order, pseudo-second-order, and intra-particle diffusion. The Lagergren pseudo-first-order model is given as follows43,44:

where qe and qt (mg g1) are the amounts of the MB degraded at equilibrium and at time t (min). k1 (min−1) is the rate constant.

Pseudo-second-order kinetic model assumes that the rate of degradation is second order45,46.

where k2 is the pseudo-second-order rate constant (Figs. 6, 7a). Tables 1 and 2 show the kinetic parameters at different shaker speeds and different temperatures (20, 40, and 70 °C) which were obtained from non-linear regression of the isotherm models. Regarding the shaking speed of 250 RPM at 303 K, the correlation coefficient is R2 = 0.79 for the first order kinetic model fitting which was low, while for the second order was about R2 = 0.94. It seems piezo degradation of MB was done through second order. By increasing the shaking speed to 350 RPM, R2 for the first and second order were close, R2 = 0.98 and 0.96 for the first and second order, respectively. R2 for the first and second order was still close by changing the mechanical force to the 250 W ultrasonic bath, 0.939 and 0.944 for the first and second order, respectively. It seems in lower shaker speed piezodegradation follows second order reaction while it follows first order in higher shaking speeds.

(a) Pseudo first-order and pseudo second-order kinetic models for degradation of 10 ppm MB in 250 W ultrasonic (red curve), reactor containing 5 ZrO2 balls shaking with 250 RPM (blue curve), and 350 RPM (black curve), (b) spectrum of MB over time in presence of S4 as catalyst and ZrO2 balls as source of mechanical force at 350 RPM. (c) spectrum of MB over time in presence of S4 as catalyst in ultrasonic bath with 250 W in power, (d) spectrum of MB over time in presence of S4 as catalyst and ZrO2 balls as source of mechanical force at 250 RPM.

(a) Pseudo first-order and pseudo second-order kinetic models for degradation of 10 ppm MB in presence of sample S4 as catalyst and ZrO2 balls with 350 RPM in speed at different temperatures: 20 °C (black curve), 40 °C (red curve), and 70 °C (blue curve). (b) LNK Vs 1/T Plot for the experimental data for the evaluation of thermodynamic Parameters of the degradation of MB. (c) Activation energy for decomposition of MB by piezo catalyst based on Arrhenius equation.

Regarding the kinetic in different temperatures, R2 of 0.79 was obtained for first-order kinetic at 293 K while R2 of 0.94 was obtained for second-order kinetic at the same temperature. R2 was 0.84 and 0.87 at 303 and 313 K, respectively for first-order fitting. For second-order fitting R2 of 0.94 was achieved at 293 K. In the case of 303 K, R2 was about 0.96 by second-order fitting. Finally, R2 was about 0.97 at 313 K. As the results show, the reaction follows second order in higher reaction temperatures. In general, it seems the piezo degradation of MB by SbSI/Sb2S3 nanocomposites follows the second-order kinetic.

The thermodynamic parameters such as entropy (∆S°), Gibbs free energy (∆G°), and enthalpy (∆Ho) for the degradation of MB by SbSI/Sb2S3 nanocomposites were calculated from the variation of Kc with temperature change of degradation and it can be determined from the following equations47,48,49:

where ∆S° is the entropy change (kJ mol−1), ∆G° is the free energy change (kJ mol−1) and ∆Ho is the enthalpy change (kJ mol−1), Ceq = Concentration of dye at equilibrium (Reactant Conc. At equilibrium), Ae = concentration of dye depredated at equilibrium (Product Conc. At equilibrium) by SbSI/Sb2S3 nanocomposites at equilibrium. The thermodynamic parameters are tabulated in (Table 2). The negative value of ∆Ho indicates the exothermic degradation of MB by SbSI/Sb2S3 nanocomposites. ∆Ho decreased by increasing the MB concentration in the degradation process. ∆Ho is − 13.7 kJ mol−1 when MB concentration was 5 ppm and it changed to − 7.7 kJ mol−1 when MB concentration increased up to 10 ppm. ∆S° for 5 ppm of MB and 10 ppm of MB was − 0.0458 kJ mol−1 and − 0.0340 kJ mol−1, respectively. ∆G° for 5 and 10 ppm of MB at 293 K was − 0.305 kJ mol−1 and 2.279 kJ mol−1, respectively. By increasing the shaking temperature to 303 K, ∆G° increased to 0.153 and 2.619 kJ mol−1 for 5 ppm and 10 ppm of MB, respectively. ∆G° at 313 K, 323 K, and 343 K could be found in Fig. 7b and Table 3. According to the results, ∆G° increased by increasing the reaction temperatures. It means the piezo degradation reaction of MB is more favorable in lower temperatures. Figure 7c shows the activation energy based on the Arrhenius equation for the decomposition of MB by SbSI/Sb2S3 nanocomposites and it was 0.148 kJ mol−1.

In summary, six types of SbSI/Sb2S3 nanocomposites synthesized via solvothermal and sonochemistry methods, whereas the SbSI/Sb2S3 nanocomposites prepared by sonochemistry (catalyst S1) in 2 h and SbSI/Sb2S3 nanocomposites prepared by solvothermal at 245 °C (catalyst S4) exhibit a higher piezocatalytic degradation performance. S4 decomposes 45.7% of MB when ultrasonic vibration with 250 W in power was used to stimulate piezo catalyst during 60 min of ultrasonication, while 89.1% of MB decomposes during 60 min by using ZrO2 balls as an alternative mechanical force to ultrasonic vibration. Changing shaking speed show dramatical effect on the degradation efficiency, so that degradation efficiency increased more than three times by increasing shaking speed from 150 to 350 RPM at 30 ± 5 °C. Temperature is another parameter that plays an important role in the degradation of MB by the SbSI/Sb2S3 nanocomposites. Degradation efficiency was increased by 42% by decreasing degradation temperature from 70 to 20 °C. Kinetic study shows that at a lower shaking speed of 250 RPM at 303 K, the correlation coefficients are R2 = 0.79 for the first-order kinetic model fitting which is low, while for the second order is about R2 = 0.94. It seems piezo degradation of MB was done through second order. By increasing the shaking speed to 350 RPM, R2 for the first and second-order are close, R2 = 0.98 and 0.96 for the first and second order, respectively. R2 for the first and second order is still close by changing the mechanical force to the 250 W ultrasonic bath, 0.939 and 0.944 for the first and second-order, respectively. It seems in lower shaker speed piezodegradation follows second order reaction while it follows first order in higher shaking speeds. As the results show, the reaction follows second order in higher reaction temperatures. In general, it seems the piezo degradation of MB by SbSI/Sb2S3 nanocomposites follows the second order kinetic. The negative value of ∆Ho indicates the degradation of MB by SbSI/Sb2S3 nanocomposites piezo catalyst is an exothermic process. According to the results, ∆G° increased by increasing the reaction temperatures. It means the piezo degradation reaction of MB is more favorable in lower temperatures.

All data generated or analysed during this study are included in this published article [and its supplementary information files].

Frolova, L. A. et al. Exploring CsPbI3–FAI alloys: Introducing low-dimensional Cs2FAPb2I7 absorber for efficient and stable perovskite solar cells. Chem. Eng. J. 426, 131754 (2021).

Article CAS Google Scholar

Yu, B.-B. et al. Heterogeneous 2D/3D tin-halides perovskite solar cells with certified conversion efficiency breaking 14%. Adv. Mater. 33, 2102055 (2021).

Article CAS Google Scholar

Tan, D. et al. Piezoelectricity in monolayer MXene for nanogenerators and piezotronics. Nano Energy 90, 106528 (2021).

Article CAS Google Scholar

Li, K. et al. High piezoelectricity of Eu3+-doped Pb(Mg1/3Nb2/3)O3–0.25PbTiO3 transparent ceramics. J. Mater. Chem. C 9, 2426–2436 (2021).

Article CAS Google Scholar

Cui, Zh. et al. Polyurethane/titania/polydopamine (TPU/TiO2/PDA) 3-D porous composite foam with outstanding oil/water separation performance and photocatalytic dye degradation. Adv. Compos. Hybrid Mater. https://doi.org/10.1007/s42114-022-00503-5 (2022).

Article Google Scholar

Guo, J. et al. Tunable negative dielectric properties of magnetic CoFe2O4/graphite-polypyrrole metacomposites. Adv. Compos. Hybrid Mater. 5, 899–906 (2022).

Article CAS Google Scholar

Guo, J. et al. Magnetic NiFe2O4/polypyrrole nanocomposites with enhanced electromagnetic wave absorption. J. Mater. Sci. Technol. 108, 64–72 (2022).

Article Google Scholar

Moradi, O., Madanpisheh, M. A. & Moghaddas, M. Synthesis of GO/HEMA, GO/HEMA/TiO2, and GO/Fe3O4/HEMA as novel nanocomposites and their dye removal ability. Adv. Compos. Hybrid Mater. 4, 1185–1204 (2021).

Article CAS Google Scholar

Xu, Q. et al. Construction of bio-piezoelectric platforms: From structures and synthesis to applications. Adv. Mater. 33, 2008452 (2021).

Article CAS Google Scholar

Mohanta, M. K., Arora, A. & Sarkar, A. D. Conflux of tunable Rashba effect and piezoelectricity in flexible magnesium monochalcogenide monolayers for next-generation spintronic devices. Nanoscale 13, 8210–8223 (2021).

Article CAS PubMed Google Scholar

Zhao, Y., Gou, G., Lu, X. & Hao, Y. Intrinsic auxeticity and negative piezoelectricity in two-dimensional group-IV dipnictide monolayers with in-plane anisotropy. J. Mater. Chem. C 9, 6068–6077 (2021).

Article CAS Google Scholar

Fu, J., Xie, A., Li, T. & Zuo, R. Ultrahigh piezoelectricity in (Ba, Ca)(Ti, Sn)O3 lead-free compounds with enormous domain wall contribution. Acta Mater. 230, 117862 (2022).

Article CAS Google Scholar

Tu, Sh. et al. Piezocatalysis and piezo-photocatalysis: Catalysts classification and modification strategy, reaction mechanism, and practical application. Adv. Funct. Mater. Organoids Tissues 30, 2005158 (2020).

Article CAS Google Scholar

Lin, P. et al. Piezo-phototronic effect for enhanced flexible MoS2/WSe2 van der Waals photodiodes. Adv. Funct. Mater. 28, 1802849 (2018).

Article CAS Google Scholar

Feng, J. et al. Enhancement and mechanism of nano-BaTiO3 piezocatalytic degradation of tricyclazole by co-loading Pt and RuO2. Environ. Sci.: Nano 6, 2241–2252 (2019).

CAS Google Scholar

Sun, J. et al. Piezo-phototronic effect enhanced efficient flexible perovskite solar cells. ACS Nano 13(4), 4507–4513 (2019).

Article CAS PubMed Google Scholar

Amiri, O. et al. Convert mechanical energy to chemical energy to effectively remove organic pollutants by using PTO catalyst. Sep. Purif. Technol. 283, 120235 (2022).

Article CAS Google Scholar

Choudhry, I., Khalid, H. R. & Lee, H.-K. Flexible piezoelectric transducers for energy harvesting and sensing from human kinematics. ACS Appl. Electron. Mater. 2(10), 3346–3357 (2020).

Article CAS Google Scholar

Aabid, A. et al. A systematic review of piezoelectric materials and energy harvesters for industrial applications. Sensors 21(12), 4145 (2021).

Article ADS PubMed PubMed Central CAS Google Scholar

Kim, T. et al. Flexible 1–3 composite ultrasound transducers with silver-nanowire-based stretchable electrodes. IEEE Trans. Ind. Electron. 67, 6955–6962 (2020).

Article Google Scholar

Ognibene, G. et al. Photoactivity of hierarchically nanostructured ZnO–PES fibre mats for water treatments. RSC Adv. 6, 42778–42785 (2016).

Article ADS CAS Google Scholar

Deak, G. et al. Synthesis of ZnO nanoparticles for water treatment applications. Int. J. Conserv. Sci. 10(2), 343–350 (2019).

CAS Google Scholar

Qian, W. et al. Piezoelectric material-polymer composite porous foam for efficient dye degradation via the piezo-catalytic effect. ACS Appl. Mater. Interfaces 11, 27862–27869 (2019).

Article CAS PubMed Google Scholar

Raju, T. D., Veeralingam, S. & Badhulika, S. Polyvinylidene fluoride/ZnSnO3 nanocube/Co3O4 nanoparticle thermoplastic composites for ultrasound-assisted piezo-catalytic dye degradation. ACS Appl. Nano Mater. 3, 4777–4787 (2020).

Article CAS Google Scholar

Xu, X., Lin, X., Yang, F., Huang, Sh. & Cheng, X. Piezo-photocatalytic activity of Bi0.5Na0.5TiO3@TiO2 composite catalyst with heterojunction for degradation of organic dye molecule. J. Phys. Chem. C 124(44), 24126–24134 (2020).

Article CAS Google Scholar

Opoku, F., Govender, K. K., Gertina, C., van Sittert, C. E. & Govender, P. P. Recent progress in the development of semiconductor-based photocatalyst materials for applications in photocatalytic water splitting and degradation of pollutants. Adv. Sustain. Syst. 1, 1700006 (2017).

Article CAS Google Scholar

Sarkar, A., Adhikary, A., Mandal, A., Chakraborty, T. & Das, D. Zn-BTC MOF as an adsorbent for iodine uptake and organic dye degradation. Cryst. Growth Des. 20, 7833–7839 (2020).

Article CAS Google Scholar

Cruz, D. R. S. et al. Magnetic nanostructured material as heterogeneous catalyst for degradation of AB210 dye in tannery wastewater by electro-Fenton process. Chemosphere 280, 130675 (2021).

Article ADS CAS PubMed Google Scholar

Schneider, J. et al. Understanding TiO2 photocatalysis: Mechanisms and materials. Chem. Rev. 114, 9919–9986 (2014).

Article CAS PubMed Google Scholar

Sakthivel, S. et al. Solar photocatalytic degradation of azo dye: Comparison of photocatalytic efficiency of ZnO and TiO2. Sol. Energy Mater. Sol. Cells 77, 65–82 (2003).

Article CAS Google Scholar

Xu, T., Zhang, L., Cheng, H. & Zhu, Y. Significantly enhanced photocatalytic performance of ZnO via graphene hybridization and the mechanism study. Appl. Catal. B 101, 382–387 (2011).

Article CAS Google Scholar

Maji, T. K., Bagchi, D., Kar, P., Karmakar, D. & Pal, S. K. Enhanced charge separation through modulation of defect-state in wide band-gap semiconductor for potential photocatalysis application: Ultrafast spectroscopy and computational studies. J. Photochem. Photobiol. A 332, 391–398 (2017).

Article CAS Google Scholar

Altfeder, I., Bianco, E. & Dorse, D. L. Self-trapping and ordering of heavy holes in the wide band-gap semiconductor β-Ga2O3. Phys. Rev. B 98, 241413 (2018).

Article ADS CAS Google Scholar

Maeda, K., Ishimaki, K., Tokunaga, Y., Lu, D. & Eguchi, M. Modification of wide-band-gap oxide semiconductors with cobalt hydroxide nanoclusters for visible-light water oxidation. Angew. Chem. Int Ed. Engl. 5, 8309–8313 (2016).

Article CAS Google Scholar

Amiri, O. et al. Purification of wastewater by the piezo-catalyst effect of PbTiO3 nanostructures under ultrasonic vibration. J. Hazard. Mater. 394, 122514 (2020).

Article CAS PubMed Google Scholar

Lin, E. et al. BaTiO3 nanocubes/cuboids with selectively deposited Ag nanoparticles: Efficient piezocatalytic degradation and mechanism. Appl. Catal. B 285, 119823 (2021).

Article CAS Google Scholar

Lei, H. et al. Efficiently harvesting the ultrasonic vibration energy of two-dimensional graphitic carbon nitride for piezocatalytic degradation of dichlorophenols. Environ. Sci.: Nano 8, 1398–1407 (2021).

CAS Google Scholar

Manoharan, S., Kesavan, D., Pazhamalai, P., Krishnamoorthy, K. & Kim, S. Ultrasound irradiation mediated preparation of antimony sulfoiodide (SbSI) nanorods as a high-capacity electrode for electrochemical supercapacitors. Mater. Chem. Front. 5, 2303 (2021).

Article CAS Google Scholar

Nowak, M. et al. Sonochemical preparation of SbSI gel. Ultrason. Sonochem. 15, 709–716 (2008).

Article CAS PubMed Google Scholar

Pathak, A. K., Prasad, M. D. & Batabyal, S. K. Onedimensional SbSI crystals from Sb, S, and I mixtures in ethylene glycol for solar energy harvesting. Appl. Phys. A: Mater. Sci. Process. 125, 213 (2019).

Article ADS CAS Google Scholar

Dashairya, L., Dasb, De. & Saha, P. Elucidating the role of graphene and porous carbon coating on nanostructured Sb2S3 for superior lithium and sodium storage. J. Alloys Compd. 883, 160906 (2021).

Article CAS Google Scholar

Li, X. et al. High performance of 3D symmetric flowerlike Sb2S3 nanostructures in dye-sensitized solar cells. Chem. A Eur. 24, 11444–11450 (2018).

Article CAS Google Scholar

Liu, Z. et al. High Curie temperature bismuth-based piezo-/ferroelectric single crystals of complex perovskite structure: Recent progress and perspectives. CrystEngComm 24, 220–230 (2022).

Article CAS Google Scholar

Ning, Zh. et al. Achieving both large piezoelectric constant and high Curie temperature in BiFeO3–PbTiO3–BaTiO3 solid solution. J. Eur. Ceram. Soc. 40, 2338–2344 (2020).

Article CAS Google Scholar

Yang, F., Zhu, X., Wu, J., Wang, R. & Ge, T. Kinetics and mechanism analysis of CO2 adsorption on LiX@ZIF-8 with core shell structure. Powder Technol. 399, 117090 (2022).

Article CAS Google Scholar

Wang, H. et al. Kinetics and mechanism study of mercury adsorption by activated carbon in wet oxy-fuel conditions. Energy Fuels 33, 1344–1353 (2019).

Article CAS Google Scholar

Simonin, J.-P. On the comparison of pseudo-first order and pseudo-second order rate laws in the modeling of adsorption kinetics. Chem. Eng. J. 300, 254–263 (2016).

Article CAS Google Scholar

Xiao, Y., Azaiez, J. & Hill, J. M. Erroneous application of pseudo-second-order adsorption kinetics model: Ignored assumptions and spurious correlations. Ind. Eng. Chem. Res. 57, 2705–2709 (2018).

Article CAS Google Scholar

Tran, H. N., You, Sh.-J. & Chao, H.-P. Thermodynamic parameters of cadmium adsorption onto orange peel calculated from various methods: A comparison study. J. Environ. Chem. Eng. 4, 2671–2682 (2016).

Article CAS Google Scholar

Download references

Authors are grateful to the council of University of Razi and University of Raparin to support this work.

Chemistry Department, College of Science, University of Raparin, Rania, Kurdistan Region, Iraq

Karukh A. Babakr, Omid Amiri, Mohammad Ali Rashi & Peshawa H. Mahmood

Faculty of Chemistry, Razi University, Kermanshah, 6714414971, Iran

Omid Amiri

Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, MI, USA

L. Jay Guo

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

K.A.B. fabricated the samples and prepared figures, O.A. wrote the manuscript, Design of the work and P.W. supervised the work, L.J.G. Writing—Review and Editing, M.A.R. and P.H.M. Analysis and interpretation of effect of balls numbers on the degradation. All authors reviewed and approved the manuscript.

Correspondence to Omid Amiri.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Babakr, K.A., Amiri, O., Guo, L.J. et al. Kinetic and thermodynamic study in piezo degradation of methylene blue by SbSI/Sb2S3 nanocomposites stimulated by zirconium oxide balls. Sci Rep 12, 15242 (2022). https://doi.org/10.1038/s41598-022-19552-3

Download citation

Received: 23 June 2022

Accepted: 31 August 2022

Published: 09 September 2022

DOI: https://doi.org/10.1038/s41598-022-19552-3

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

Scientific Reports (2023)

Scientific Reports (2022)

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.